Question: What Is The Break In Period For A New Harley?

How do you break in a brand new motorcycle?

For the first 500 to 1,000 miles, avoid using more than ¾ throttle.

Always avert high engine speeds.

Do not make hard stops, aggressive starts, or rapid acceleration unless there is an emergency.

While breaking-in your motorcycle, increase your bike’s engine speed to the rev limit for short time periods..

How many miles should a new motorcycle have?

3 to 5 miles on the odometer when you take delivery is reasonable, and should be expected. As others have stated, what matters is the “Out The Door” price you pay for the bike. There are other lengthy threads on the forum, such as “What did you pay for your bike”, etc.

How do I reset my Harley ECM?

Resetting ECM… Turning the ignition on/off three times will reset the ECM when the “limp home” mode is in effect. This will usually clear it.

Do Harleys break down alot?

Harleys break down for several reasons. A major reason is the predisposition of Harley owners to modify their motorcycles excessively. Often, people perform these modifications without expert guidance and cause problems for the bikes later on. There is also the failure of Harley owners to maintain their bikes properly.

What is done on a 1000 mile Harley service?

Harley-Davidson 1,000-Mile Service Checklist Inspect engine oil and filter. Inspect oil lines and brake system for leaks. Inspect air cleaner and service as required. Check tire pressure and inspect tread.

How much does a 10000 mile Harley service cost?

RE: 10K Mile Service Cost The 10,000 service is $400 with Synthetic.

Is it necessary to break in a new motorcycle?

It’s important to break in a new motorcycle engine correctly, or you risk impairing it’s performance or damaging it outright.

Do new engines need to be broken in?

Most experts consider the first 500 miles as a reasonable and sufficient break-in period. The reasoning behind this practice is that keeping revs relatively low helps the piston rings seal against the cylinder bores properly. … However, when a car is new, these bands need time to settle within the cylinders.

What does the red light on a Harley speedometer mean?

That little lite is telling you something is wrong with the bike. With the Ignition switch off, put the bike into the “run” position, then turn on the ignition. This should put your bike into diagnostics mode.

How do you break in a new Harley Davidson?

Break-In Riding ProcedureDuring the first 50 miles of riding, keep the engine speed below 3,000 RPM (5,000 RPM for VRSC™) in any gear. … Up to 500 miles, vary the engine speed and avoid operating at any speed for long periods. … Drive slowly and avoid fast starts at wide-open throttle until the engine has warmed up.More items…

How often should you change your Harley oil?

every five thousand milesHarley-Davidson® recommends that your motorcycle receive servicing at least every five thousand miles, depending upon rider, riding style and conditions. Sometimes more frequent oil changes can be warranted.

How many miles does a motorcycle engine last?

It might last 10,000 miles. if the same engine with old fashioned 10w-40 mineral oil starts from cold twice a day and goes 10 miles each time at more or less full speed. It will last 20,000 miles…. Same number of cold starts, but twice the ‘hot’ mileage…

How do I run a diagnostic on my Harley?

To get the DTC within an area of diagnostics, push and hold the odometer reset button in for 5 seconds and release. If there are any DTC’s the code will be displayed or the word “none” will appear if there are no DTC’s. Push the odometer reset button again to view additional codes if they exist. 1 – Record the codes.

How many miles will a Harley Davidson last?

For sports bikes, 25,000 miles can be a lot. Harley-Davidson® motorcycles are built to last much longer. If a bike has good maintenance records, no signs of damage and no oil leaks, even a bike with 40,000 to 50,000 miles can be expected to last a long time.